The best materials for aerospace and defense parts depend on what the part has to do: carry load, shed weight, survive heat, resist corrosion, or insulate. There’s no single answer, but there is a short list. Aluminum, titanium, stainless steel, and nickel alloys cover most structural and high-heat needs, while advanced plastics like PEEK and Ultem take over where weight, insulation, or chemical resistance matter more.
Here’s how the main options compare, what to consider before choosing, and how material sourcing affects the finished part. We machine many of these materials at Reading Advanced Machining (RAM), and we’ll be clear about which.
The table below summarizes typical use cases. Values and suitability vary by alloy and grade, so confirm against the specification for your program.
| Material | Strengths | Typical uses | Machining notes |
|---|---|---|---|
| Aluminum alloys (2024, 6061, 7075) | High strength-to-weight, corrosion resistance, easy to machine | Fuselage skins, wing structures, fuel tanks, brackets, interior frames | Machines readily |
| Titanium alloys | Very high strength-to-weight; corrosion and heat resistance (about 1,000°F) | Landing gear, engine parts, airframe components | Harder to machine; slower cutting |
| Stainless steel | Corrosion and heat resistance, durability | Fasteners, joints, landing gear, engine components | Moderate |
| Nickel alloys (e.g., Inconel) | Strength from about -238°F to 1,800°F and above; oxidation resistance | Turbine blades, combustion chambers, exhaust systems | Among the most difficult to machine |
| PEEK | Strength and fine tolerances at high temperature, low weight | Engine components, brackets, structural parts | Stable; wears tools |
| Ultem | High dielectric strength, flame resistance | Cabin components, electrical insulation | Anneal before machining |
| Torlon / Vespel | Wear resistance, high heat, low friction | Bushings, bearings, seals, vacuum hardware | Specialized tooling and process |
These ranges come from published guidance on common aerospace metals and general materials references.
Choose aluminum when weight and machinability matter and the part isn’t facing extreme heat. Its high strength-to-weight ratio and corrosion resistance make it a default for fuselage skins, wing structures, fuel tanks, and interior frames. Common aerospace grades include 2024 for strength and fatigue resistance, 6061 for general structural and fittings use, and 7075 for the highest-strength structural parts.
Titanium makes sense when you need high strength at low weight and the part sees heat or demanding loads. Titanium alloys resist corrosion and handle temperatures around 1,000°F, with good fatigue resistance, which is why they appear in landing gear, engine parts, and airframes. The trade-off is cost and machinability: titanium cuts slowly and wears tools, so plan for both in your schedule and budget. We machine titanium alongside aluminum, brass, copper, and stainless steel.
Stainless steel is the practical choice for corrosion-prone joints, fasteners, and components that absorb repeated impact. Nickel alloys such as Inconel go further, holding strength across extreme temperature ranges, which is why they’re used in turbine blades and exhaust systems. They’re also among the hardest metals to machine, so ask any prospective shop whether it has real experience with the specific alloy before you commit. If a program calls for superalloys, tell us the alloy up front so we can confirm fit rather than guess.
Plastics fit where metals are heavier or less suitable. PEEK handles high-temperature structural parts with fine tolerances. Ultem insulates electrically and resists flame. Torlon and Vespel serve high-wear, high-heat, and vacuum applications, and PTFE covers seals and low-friction needs. Many programs use metals and plastics side by side, and we machine both under the same quality system. For more on two of these, see our guide to Vespel and Torlon machining.
Because a perfect part machined from the wrong or undocumented material isn’t acceptable in these industries. Source materials that are fully traceable from mill to distributor, and work with qualified, certified suppliers. Higher-quality material may cost more upfront, but it tends to extend component life and reduce maintenance cost.
That philosophy runs through how we work. As our president, Tom Funk, puts it, “Use only quality materials that have been stress relieved. Materials that are certified and traceable.” We provide lot and batch traceability, we hold AS9100D and ISO 9001:2015 certifications, and we’re ITAR registered, so defense and aerospace customers get both the part and the paperwork. Our military and defense capabilities cover components for land, sea, and air.
What metals are most common in aerospace manufacturing?
Aluminum alloys, titanium alloys, stainless steel, and nickel alloys are the most common, each chosen for a different balance of weight, strength, heat resistance, and corrosion resistance.
Which aerospace material is lightest?
Among common metals, aluminum is the lightest. Advanced plastics like Torlon and Vespel weigh roughly half as much as aluminum.
Is titanium harder to machine than aluminum?
Yes. Titanium is stronger and cuts more slowly, with more tool wear, so it takes longer and costs more to machine.
Does RAM machine titanium and plastics for defense work?
We machine titanium, aluminum, stainless steel, brass, copper, and advanced plastics, and we’re ITAR registered for defense work. For specialty alloys, contact us with your specification.
What does material traceability mean?
It means each batch of raw material can be tracked back to its source with documentation, so every finished part can be tied to certified material.
If you’re selecting materials for an aerospace or defense program, request a quote or call 610-926-3245. Send us your drawing and material callout, and we’ll let you know how we’d approach it.