Machined Plastic Parts for Aerospace: Materials That Perform Under Stress

aerospace plastic machined partsAerospace plastic machined parts have a bigger job than most people expect. They insulate wiring, carry bearing loads, seal against jet fuel, and hold shape across wide temperature swings, all while weighing a fraction of the metal they replace. The right plastic can take weight out of an aircraft without giving up reliability. The wrong one can crack, creep, or outgas where it shouldn’t.

Here’s how the main aerospace plastics compare, where each one is used, and what it takes to machine them well.

Key Takeaways

Why Do Aerospace Programs Use Plastic at All?

Aerospace programs use plastic to cut weight, resist corrosion and chemicals, insulate electrically, and reduce friction, in places where metal is heavier or less suited. The development of high-performance plastics since the early 1960s has been driven largely by aerospace and nuclear technology, as described in this overview of high-performance plastics.

The weight advantage is easy to quantify. Torlon and Vespel have a specific gravity around 1.4, roughly half that of aluminum. On a platform where every gram counts, that adds up fast.

Which Plastics Are Used in Aerospace Parts?

Five materials cover most aerospace plastic machined parts.

PEEK. A strong semi-crystalline thermoplastic that supports fine tolerances and withstands high temperature, with a continuous service temperature around 250°C. It’s used in engine components, brackets, and structural parts where metal replacement is the goal.

Ultem (PEI). An amorphous thermoplastic with some of the highest dielectric strength of any thermoplastic, plus strong flame resistance. It’s common in aircraft interiors and for electrical insulation. For more detail, see our guide to Ultem machining.

Torlon (PAI). A polyamide-imide with exceptional strength and wear resistance at high temperature. It’s used for bushings in engines, bearings, and seals that contact jet fuel or de-icing fluids.

Vespel (polyimide). Valued for low friction, high-temperature performance, and very low outgassing, which makes it a fit for vacuum, space, and high-wear applications.

PTFE. The lowest-friction option, used in low-friction bearings and insulation, with outstanding chemical inertness.

What Parts Are Typically Machined From Aerospace Plastics?

Our aerospace work covers seals, gears, bushings, cams, and rollers, and many of the same part types show up across the industry. Typical examples include:

How Do You Machine These Plastics to Aerospace Tolerances?

You machine them with controlled processes, because aerospace plastics don’t forgive guesswork. A few examples of what matters:

We hold tolerances as tight as +/-.001″ on many of these materials, and all parts go through quality inspection before shipping. Because aerospace customers often need paperwork as much as parts, we provide lot and batch traceability and hold AS9100D and ISO 9001:2015 certifications.

What Should You Ask Before Choosing a Material or Shop?

Start with the environment: temperature range, fluids, load, vacuum, and electrical needs. Then ask a prospective shop how they’d machine your specific material, how they control stress and heat, and how they document traceability. A shop that can describe its process in detail has usually done the work before.

You can also see which materials we stock on our aerospace industry page, which lists the types of plastic and metal parts we machine for aviation and aerospace customers.

FAQ

What is the best plastic for aerospace parts?
There isn’t one. PEEK suits structural and high-heat parts, Ultem suits insulation and cabin components, Torlon suits wear under load, and Vespel suits extreme heat and vacuum.

Why use plastic instead of metal in aircraft?
Mainly weight savings, corrosion resistance, electrical insulation, and low friction. High-performance plastics are about half the density of aluminum.

Can machined plastics handle jet fuel and de-icing fluids?
Some can. Torlon, for example, is used in seals that contact jet fuel and de-icing fluids, but always confirm chemical compatibility for your specific grade and fluid.

What tolerances can machined aerospace plastics hold?
With proper tooling, stress relief, and fixturing, we hold tolerances as tight as +/-.001″ on many plastic parts.

Does RAM have aerospace quality certification?
Yes. RAM is AS9100D certified, holds ISO 9001:2015 certification, and is ITAR registered.

Talk With Our Team About Your Aerospace Part

If you’re specifying a plastic for an aerospace application, request a quote or call 610-926-3245. We’ll help you weigh materials, tolerances, and documentation before you commit.

We guarantee our parts
will deliver for you.

Request a Quote