Machined Plastic Parts for Medical Devices: Material Considerations

medical device plastic partsMedical device plastic parts have a hard life. They’re cleaned with harsh disinfectants, cycled through autoclaves, handled constantly, and expected to hold their dimensions the whole time. Choosing the plastic is usually the decision that determines whether a part lasts for years or cracks after a few dozen sterilization cycles.

At Reading Advanced Machining (RAM), we machine medical components from high-performance plastics every day. This post walks through the material properties that matter most and how the common choices compare.

Key Takeaways

What Counts as a Medical Device?

A medical device is a broad category. The FDA defines a device as an instrument, apparatus, implement, machine, implant, or similar article intended for diagnosing, treating, or preventing disease, and it sorts devices into Class I, II, and III by risk.

That range matters for plastic parts. A knob on a lab analyzer, a sterilizable instrument handle, and a component inside a diagnostic system all count as medical device plastic parts, but they face very different conditions. The device maker sets the regulatory path; the material and machining need to support it.

Which Properties Matter Most for Medical Plastic Parts?

Five properties usually drive the decision:

  1. Sterilization resistance. How many cycles of steam, chemical, or radiation exposure can the part survive without cracking, warping, or losing strength?
  2. Chemical resistance. Hospital disinfectants and cleaning agents can cause stress cracking in some plastics.
  3. Dimensional stability. Moisture absorption and heat can move a part out of tolerance.
  4. Strength and stiffness. Instrument handles, levers, and structural parts need to resist bending and wear.
  5. Biocompatibility. Parts that contact patients need grades tested to standards such as ISO 10993 or USP Class VI.

How Do the Common Medical Plastics Compare?

PEEK. Strong, stiff, and chemically resistant, PEEK handles repeated steam sterilization and high temperatures well. It’s one of the most expensive plastics we machine, so it’s usually reserved for parts where its performance is needed.

Radel (PPSU). Radel is widely used for sterilization trays, instrument handles, and reusable device components because it tolerates many autoclave cycles and has high impact strength. It costs less than PEEK.

Ultem (PEI). Ultem offers high heat resistance, stiffness, and good dimensional stability. It’s a solid choice for equipment and instrument parts, though some cleaning chemicals can stress-crack it, so the cleaning regimen should be checked.

Acetal (Delrin). Acetal machines cleanly and holds tight tolerances, which makes it popular for prototypes and non-critical device parts. It has limited tolerance for repeated high-heat sterilization.

PTFE. PTFE is nearly inert chemically and has very low friction. It’s soft and creeps under load, so it suits seals, liners, and low-load parts more than structural ones.

These are general patterns. Properties vary by grade and supplier, so the manufacturer’s data sheet should confirm the final choice. We stock all of these, along with medical grade plastics, on our plastic distribution list.

What About Biocompatibility?

Biocompatibility means a material doesn’t cause a toxic or allergic reaction for its intended use. For plastics, that’s established by testing a specific grade, not the polymer family in general. A natural, medical-grade PEEK and an industrial filled PEEK can behave very differently in the body.

Our introduction to biocompatible plastics explains how materials are grouped by contact type and duration. On our side, we machine from certified, traceable stock so the material documentation can travel with the parts.

How Does Machining Affect a Plastic Medical Part?

Machining can add stress, heat, and surface damage that show up later as cracking or dimensional drift. Sharp tooling, controlled feeds and speeds, proper annealing where the material calls for it, and work-holding that doesn’t distort the part all help.

We use stress-relieved material, Renishaw probing for tool and fixture offsets, and vacuum work-holding on our machines. Every part passes an ISO 9001:2015-compliant inspection before shipping, and we hold tolerances as tight as +/-.001″ on many plastic parts.

FAQ

What is the best plastic for medical device parts? There isn’t one best plastic. PEEK and Radel are common for parts that see repeated steam sterilization, Ultem for heat-resistant equipment parts, and acetal or PTFE for lower-heat or low-friction applications.

Can plastic medical parts go in an autoclave? Many can. PEEK and Radel are known for handling repeated autoclave cycles. Acetal and some other plastics are better suited to limited cycles or other sterilization methods.

Are all PEEK parts biocompatible? No. Biocompatibility depends on the specific grade and its testing, such as ISO 10993 or USP Class VI. Filled or industrial grades may not qualify.

Does RAM machine medical-grade plastics? Yes. We machine and stock PEEK, Radel, Ultem, PTFE, acetal, and other medical grade plastics.

Get Your Medical Plastic Parts Quoted

When your print is ready, we’re ready to machine it. Request a quote or call 610-926-3245, and see more about our medical industry capabilities.

We guarantee our parts
will deliver for you.

Request a Quote