Plastic vs. Metal Machined Parts: How to Weigh the Trade-offs

Every design eventually hits the same fork: should this part be plastic or metal? When it comes to plastic vs metal machined parts, there’s no universal winner. Metal usually wins on raw strength and heat, plastic often wins on weight, corrosion, friction, and electrical insulation, and the right call depends on what the part actually has to survive.

At Reading Advanced Machining (RAM), we machine both, so we see the decision from either side. Here’s how the trade-offs break down.

Key Takeaways

How Do Plastic and Metal Machined Parts Differ?

Plastic and metal differ most in strength, stiffness, weight, heat tolerance, and how they respond to cutting. A general comparison of plastic and metal in CNC machining summarizes it well: metals are harder and stronger and handle heat and heavy wear better, while plastics are lighter, cheaper in many cases, and gentler on cutting tools.

In practice, the differences show up like this:

Factor Metal (aluminum, steel, titanium) Plastic (engineering and high-performance)

Strength and stiffness

Higher

Lower, though advanced grades come close for many uses

Density

Aluminum about 2.7 g/cm³; steel about 7.8

Roughly 1.4–1.65 for high-performance plastics like Torlon and Vespel

Heat limit

Very high

Typically 120–260°C depending on the plastic

Corrosion

Varies; may need coating

Generally excellent; PTFE is near-inert

Electrical

Conductive

Insulating (or static-dissipative if specified)

Thermal expansion

Aluminum about 23 × 10⁻⁶/°C

Often 3–10 times higher

Tool wear while machining

Higher

Lower

When Does Plastic Make Sense Instead of Metal?

Plastic makes sense when weight, corrosion, friction, noise, or electrical insulation matter more than raw strength. A few common cases:

If you’re specifically weighing PEEK against metal, our guide to PEEK vs. metal parts covers the details.

When Is Metal the Better Choice?

Metal is the better choice when the part carries high loads, sees sustained heat beyond what plastics tolerate, or must stay dimensionally stable across large temperature swings. Aluminum, brass, copper, stainless steel, and titanium cover most needs, and we machine all of them to the same tight tolerances we hold on plastic.

Metal also has the edge when the part is structural, thin-walled under load, or in constant impact. Plastics can crack or deform under stresses that metals shrug off.

What Does Thermal Expansion Mean for Your Design?

It means you can’t treat the two materials the same in an assembly. Most plastics expand and contract three to ten times more than metals as temperature changes. PTFE, for example, expands at roughly 112–135 × 10⁻⁶/°C, compared with about 23 × 10⁻⁶/°C for aluminum.

If a plastic part presses into a metal housing, a temperature swing can loosen the fit or build stress that causes failure. Glass or carbon fillers lower a plastic’s expansion, and a good design leaves room for the difference. This is one of the first things we check when reviewing a drawing for a mixed plastic-and-metal assembly.

How Do They Compare on Cost and Machinability?

Commodity plastics are inexpensive and cut quickly, but that’s not the full picture. High-performance plastics can cost more per pound than common metals. Published market figures put PEEK near $100 per kilogram, while the average high-performance plastic sits closer to $15 per kilogram.

Machinability cuts both ways. Plastics are gentler on tools, but they flex away from the cutting edge, can grab and gum up tooling, and respond to heat and clamping pressure in ways metal doesn’t. That’s why work-holding matters: our machines use vacuum portals and carefully developed fixturing so parts stay motionless without being squeezed out of shape. Whichever material you choose, our CNC manufacturing capabilities cover both.

FAQ

Is plastic as strong as metal? Not generally. Metals are stronger and stiffer, but advanced plastics like PEEK and Torlon deliver enough strength for many applications at a fraction of the weight.

Which is cheaper to machine, plastic or metal? Plastic is usually quicker to cut and easier on tools, but advanced plastics can have high material costs. The total depends on the specific material and the part’s tolerances.

Can plastic parts hold the same tolerances as metal? Often, yes. We hold tolerances as tight as +/-.001″ on many plastic parts, though thermal expansion and moisture absorption need to be accounted for in the design.

Can plastic withstand high temperatures? Standard plastics can’t, but high-performance grades like PEEK, Torlon, and Vespel run continuously at roughly 250°C and above.

Can I mix plastic and metal in one assembly? Yes, and it’s common. Just design for the difference in thermal expansion so fits stay reliable across the operating temperature range.

Get a Second Opinion Before You Commit to a Material

Not sure whether plastic or metal is right for your part? Request a quote or call 610-926-3245, and our team can review your drawing and recommend a material that fits the application and the budget.

We guarantee our parts
will deliver for you.

Request a Quote